Crawler tracks

Share your building instructions or ask questions about constructing your robot
bullestock
Posts: 27
Joined: 29 Sep 2010, 19:34
Location: Denmark
Contact:

Re: Crawler tracks

Post by bullestock »

marcoloca wrote:
hassenplug wrote: I would connect the motor to the middle hub to give it good ground clearance, but only if the track goes around 90 degrees of the hub. Less than that, and it may slip.
Sorry, I don't understand "goes around 90 degrees of the hub"...
The track needs to touch the hub (wheel) for at least a quarter of the hub - look at this picture:

http://en.wikipedia.org/wiki/File:Track ... ram%29.png

Here, 1 and 4 would be good places to attach the motor, but 5 and 6 would be bad choices, because there is too little contact between hub and track.
h-g-t
Posts: 552
Joined: 07 Jan 2011, 08:59
Location: Albania

Re: Crawler tracks

Post by h-g-t »

If your vehicle is mainly moving forward, driving the back (wheel 5 on the diagram) is best.

The lower track is being pulled straight by the rotation of the drive wheel so is less likely to jump off the wheels.

Of course, when going in the other direction it is being pushed so not kept tight.

If it will spend the same time in either direction the the 3-point solution (top wheel driven) should be better but there is greater chance of the track jumping the drive wheel.

You might be able to get round this by having another wheel (with a tyre) on top of the track pushing it down onto the sprocket.

Alternatively, you could have a tensioner wheel (either inside or outside of the track) which keeps it all fairly taut.

This could be on a pivot and operated by a rubber band or spring).
A sophistical rhetorician, inebriated with the exuberance of his own verbosity, and gifted with an egotistical imagination that can at all times command an interminable and inconsistent series of arguments to malign an opponent and to glorify himself.
marcoloca
Posts: 12
Joined: 19 Jan 2012, 16:32

Re: Crawler tracks

Post by marcoloca »

bullestock wrote: The track needs to touch the hub (wheel) for at least a quarter of the hub - look at this picture:

http://en.wikipedia.org/wiki/File:Track ... ram%29.png

Here, 1 and 4 would be good places to attach the motor, but 5 and 6 would be bad choices, because there is too little contact between hub and track.
Thanks, now I understand! I'll see tomorrow in the laboratory =)
h-g-t wrote:If your vehicle is mainly moving forward, driving the back (wheel 5 on the diagram) is best.

The lower track is being pulled straight by the rotation of the drive wheel so is less likely to jump off the wheels.

Of course, when going in the other direction it is being pushed so not kept tight.

If it will spend the same time in either direction the the 3-point solution (top wheel driven) should be better but there is greater chance of the track jumping the drive wheel.

You might be able to get round this by having another wheel (with a tyre) on top of the track pushing it down onto the sprocket.

Alternatively, you could have a tensioner wheel (either inside or outside of the track) which keeps it all fairly taut.

This could be on a pivot and operated by a rubber band or spring).
Our robot must turn and go backwards sometime... I think it's better trying to connect the motor to the middle high hub. Other more complicated methods are unsuitable for our simple robot, sorry =)
h-g-t
Posts: 552
Joined: 07 Jan 2011, 08:59
Location: Albania

Re: Crawler tracks

Post by h-g-t »

A sophistical rhetorician, inebriated with the exuberance of his own verbosity, and gifted with an egotistical imagination that can at all times command an interminable and inconsistent series of arguments to malign an opponent and to glorify himself.
spillerrec
Posts: 358
Joined: 01 Oct 2010, 06:37
Location: Denmark
Contact:

Re: Crawler tracks

Post by spillerrec »

What is the advantage of positioning the threads in this kind of triangular fashion? I would think that to get maximum grip you would want to have as much tread touching the ground, however a triangular design would reduce this a little.

Just to make sure it is mentioned, the rubber tracks do require quite a bit more power to turn them, because of the internal friction in the tracks. The thread links do not have this issue but since they are of plastic they have very little traction on hard surfaces.
My blog: http://spillerrec.dk/category/lego/
RICcreator, an alternative to nxtRICeditV2: http://riccreator.sourceforge.net/
h-g-t
Posts: 552
Joined: 07 Jan 2011, 08:59
Location: Albania

Re: Crawler tracks

Post by h-g-t »

I think the main advantage is that the lower track is under tension whichever direction you are going.

It might also help to improve ground clearance under the centre of the vehicle by keeping the gears, differentials, etc higher up.

Probably does not improve the stability by putting weight up higher though.
A sophistical rhetorician, inebriated with the exuberance of his own verbosity, and gifted with an egotistical imagination that can at all times command an interminable and inconsistent series of arguments to malign an opponent and to glorify himself.
jwiger
Posts: 125
Joined: 24 May 2011, 20:41
Location: Where ever the military sends me (currently Central Texas)
Contact:

Re: Crawler tracks

Post by jwiger »

I would connect the motor to the middle hub to give it good ground clearance, but only if the track goes around 90 degrees of the hub. Less than that, and it may slip.
Sorry, I don't understand "goes around 90 degrees of the hub"...
The track should contact 1/4 (25%) of the driving wheel hub, or more. I would recommend the front or back (anterior or posterior) since most track designs (re: a bulldozer) have almost 1/2 (50%) of the wheel hub in contact with the track.
JimmyJam
"The more you know, the more you know, the less you know."
pepijndevos
Posts: 175
Joined: 28 Dec 2011, 13:07
Location: Gelderland, Netherlands
Contact:

Re: Crawler tracks

Post by pepijndevos »

mightor wrote:At my robotics club we have competitions and the robots with the tracks often find themselves unable to make a pivot turn on the rubber mats due to the friction. I've seen tracks split or just come off the little wheels. Keep that in mind :)

- Xander
Where is this club?
-- Pepijn
http://studl.es Mindstorms Building Instructions
mightor
Site Admin
Posts: 1079
Joined: 25 Sep 2010, 15:02
Location: Rotterdam, Netherlands
Contact:

Re: Crawler tracks

Post by mightor »

We get together in Sint-Katelijne-Waver in Belgium. It's quite close, about an hour from R'dam. More info: http://wiki.robotmc.org/index.php?title=Hoofdpagina

- Xander
| My Blog: I'd Rather Be Building Robots (http://botbench.com)
| RobotC 3rd Party Driver Suite: (http://rdpartyrobotcdr.sourceforge.net)
| Some people, when confronted with a problem, think, "I know, I'll use threads,"
| and then two they hav erpoblesms. (@nedbat)
Post Reply

Who is online

Users browsing this forum: No registered users and 6 guests